STUDENT GRADER Total Score I am submitting my own work, and I understand penalties will be assessed if I submit work for credit that is not my own. Print Name ID Number Sign Name Date # Points Score 1 4 2 8 3 6 4 12 5 4 6 10 7 8 8 6 9 6 Weeks late Adjusted Score Estimated Work Hours 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 Overall Weight Adjusted Score: Deduct 20% from score for each week late Problem 1. Sketch circuits for the following logic equations. Y <= (A and B and C) or not ((A and not B and C and not D) or not (B or D)); X <= (A xor (B and C) xor not D) or (not (B xor C) and not (C or D)) Problem 2. Sketch circuits and write VHDL assignment statements for the following equations. F = m(1, 2, 6) F = M(0, 7) Problem 3. Write logic assignment statements for the following circuit. Problem 4: Sketch circuits and write VHDL assignment statements for the truth tables below. Problem 5: Sketch POS circuits for the 2XOR and 2XNOR functions. Problem 6: Sketch the circuit described by the netlist shown, and complete the timing diagram for the stimulus shown to document the circuit’s response to the example stimulus. Use a 100ns vertical grid in your timing diagram, and show all inputs and outputs. Problem 7: Create a truth table that corresponds to the simulation shown below. Show all input and output values in the truth table, and sketch a logic circuit that could have been used to create the waveform. Problem 8. The Seattle Mariners haven’t had a stolen base in 6 months, and the manager decided it was because the other teams were reading his signals to the base runners. He came up with a new set of signals (pulling on his EAR, lifting one LEG, patting the top of his HEAD, and BOWing) to indicate when runners should attempt to steal a base. A runner should STEAL a base if and only if the manager pulls his EAR and BOWs while patting his HEAD, or if he lifts his LEG and pats his HEAD without BOWing, or anytime he pulls his EAR without lifting his LEG. Sketch a minimal circuit that could be used to indicate when a runner should steal a base. Problem 9. A room has four doors and four light switches (one by each door). Sketch a circuit that allows the four switches to control the light – each switch should be able to turn the light on if it is currently off, and off if it is currently on. Note that it will not be possible to associate a given switch position with “light on” or “light off” – simply moving any switch should modify the light’s status.

STUDENT GRADER Total Score I am submitting my own work, and I understand penalties will be assessed if I submit work for credit that is not my own. Print Name ID Number Sign Name Date # Points Score 1 4 2 8 3 6 4 12 5 4 6 10 7 8 8 6 9 6 Weeks late Adjusted Score Estimated Work Hours 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 Overall Weight Adjusted Score: Deduct 20% from score for each week late Problem 1. Sketch circuits for the following logic equations. Y <= (A and B and C) or not ((A and not B and C and not D) or not (B or D)); X <= (A xor (B and C) xor not D) or (not (B xor C) and not (C or D)) Problem 2. Sketch circuits and write VHDL assignment statements for the following equations. F = m(1, 2, 6) F = M(0, 7) Problem 3. Write logic assignment statements for the following circuit. Problem 4: Sketch circuits and write VHDL assignment statements for the truth tables below. Problem 5: Sketch POS circuits for the 2XOR and 2XNOR functions. Problem 6: Sketch the circuit described by the netlist shown, and complete the timing diagram for the stimulus shown to document the circuit’s response to the example stimulus. Use a 100ns vertical grid in your timing diagram, and show all inputs and outputs. Problem 7: Create a truth table that corresponds to the simulation shown below. Show all input and output values in the truth table, and sketch a logic circuit that could have been used to create the waveform. Problem 8. The Seattle Mariners haven’t had a stolen base in 6 months, and the manager decided it was because the other teams were reading his signals to the base runners. He came up with a new set of signals (pulling on his EAR, lifting one LEG, patting the top of his HEAD, and BOWing) to indicate when runners should attempt to steal a base. A runner should STEAL a base if and only if the manager pulls his EAR and BOWs while patting his HEAD, or if he lifts his LEG and pats his HEAD without BOWing, or anytime he pulls his EAR without lifting his LEG. Sketch a minimal circuit that could be used to indicate when a runner should steal a base. Problem 9. A room has four doors and four light switches (one by each door). Sketch a circuit that allows the four switches to control the light – each switch should be able to turn the light on if it is currently off, and off if it is currently on. Note that it will not be possible to associate a given switch position with “light on” or “light off” – simply moving any switch should modify the light’s status.

info@checkyourstudy.com
ELEC153 Circuit Theory II M2A3 Lab: AC Series Circuits Introduction Previously you worked with two simple AC series circuits, R-C and R-L circuits. We continue that work in this experiment. Procedure 1. Setup the following circuit in MultiSim.The voltage source is 10 volts peak at 1000 Hz. Figure 1: Circuit for analysis using MultiSim 2. Change R1 to 1 k and C1 to 0.1 uF. Connect the oscilloscope to measure both the source voltage and the voltage across the resistor.You should have the following arrangement. Figure 2: Circuit of figure 1 connected to oscilloscope To color the wires, right click the desired wire and select “Color Segment…” and follow the instructions. Start the simulation and open the oscilloscope. You should get the following plot: Figure 3: Source voltage (red) and the voltage (blue) across the resistor The red signal is the voltage of the source and the blue is the voltage across the resistor. The colors correspond to the colors of the wires from the oscilloscope. 3. From the resulting analysis plotdetermine the peak current. To determine the peak current measure the peak voltage across the resistor and divide by the value of the resistor (1000 Ohms). Record it here. Measured Peak Current 4. Determine the peak current by calculation. Record it here. Does it match the measured peak current? Explain. Calculated Peak Current 5 Determine the phase shift between the current in the circuit and the source voltage. We look at the time between zero crossings to determine the phase shift between two waveforms. In our plot, the blue waveform (representing the circuit current or the voltage across the resistor) crosses zero before the red waveform (the circuit voltage). So, current is leading voltage in this circuit. This is exactly what should happen when we have a capacitive circuit. 6. To determine the phase shift, we first have to measure the time between zero crossings on the red and blue waveforms. This is done by moving the oscillator probes to the two zero crossing as is shown in the following figure Figure 4: Determining the phase shift between the two voltage waveforms We can see from the figure that the zero crossing difference (T2 – T1) is approximately 134 us. The ratio of the zero-crossing time difference to the period of the waveform determines the phase shift, as follows: Using our time values, we have: How do we know if this phase shift is correct? In step 4 when you did your manual calculations to find the peak current, you had to find the total impedance of the circuit, which was: Now, the current will be: Here, the positive angle on the current indicates it is leading the circuit voltage. 7. Change the frequency of the voltage source to 5000 Hz. Estimulate and perform a Transient Analysis to find the new circuit current and phase angle. Measure them and record them here: Measured Current Measured Phase Shift 8. Perform the manual calculations needed to find the circuit current and phase shift. Record the calculated values here. Do they match the measured values within reason? What has happened to the circuit with an increase in frequency? Calculated Current Calculated Phase Shift Writeup and Submission In general, for each lab you do, you will be asked to setup certain circuits, simulate them, record the results, verify the results are correct by hand, and then discuss the solution. Your lab write-up should contain a one page, single spaced discussion of the lab experiment, what went right for you, what you had difficulty with, what you learned from the experiment, how it applies to our coursework, and any other comment you can think of. In addition, you should include screen shots from the MultiSim software and any other figure, table, or diagram as necessary.

ELEC153 Circuit Theory II M2A3 Lab: AC Series Circuits Introduction Previously you worked with two simple AC series circuits, R-C and R-L circuits. We continue that work in this experiment. Procedure 1. Setup the following circuit in MultiSim.The voltage source is 10 volts peak at 1000 Hz. Figure 1: Circuit for analysis using MultiSim 2. Change R1 to 1 k and C1 to 0.1 uF. Connect the oscilloscope to measure both the source voltage and the voltage across the resistor.You should have the following arrangement. Figure 2: Circuit of figure 1 connected to oscilloscope To color the wires, right click the desired wire and select “Color Segment…” and follow the instructions. Start the simulation and open the oscilloscope. You should get the following plot: Figure 3: Source voltage (red) and the voltage (blue) across the resistor The red signal is the voltage of the source and the blue is the voltage across the resistor. The colors correspond to the colors of the wires from the oscilloscope. 3. From the resulting analysis plotdetermine the peak current. To determine the peak current measure the peak voltage across the resistor and divide by the value of the resistor (1000 Ohms). Record it here. Measured Peak Current 4. Determine the peak current by calculation. Record it here. Does it match the measured peak current? Explain. Calculated Peak Current 5 Determine the phase shift between the current in the circuit and the source voltage. We look at the time between zero crossings to determine the phase shift between two waveforms. In our plot, the blue waveform (representing the circuit current or the voltage across the resistor) crosses zero before the red waveform (the circuit voltage). So, current is leading voltage in this circuit. This is exactly what should happen when we have a capacitive circuit. 6. To determine the phase shift, we first have to measure the time between zero crossings on the red and blue waveforms. This is done by moving the oscillator probes to the two zero crossing as is shown in the following figure Figure 4: Determining the phase shift between the two voltage waveforms We can see from the figure that the zero crossing difference (T2 – T1) is approximately 134 us. The ratio of the zero-crossing time difference to the period of the waveform determines the phase shift, as follows: Using our time values, we have: How do we know if this phase shift is correct? In step 4 when you did your manual calculations to find the peak current, you had to find the total impedance of the circuit, which was: Now, the current will be: Here, the positive angle on the current indicates it is leading the circuit voltage. 7. Change the frequency of the voltage source to 5000 Hz. Estimulate and perform a Transient Analysis to find the new circuit current and phase angle. Measure them and record them here: Measured Current Measured Phase Shift 8. Perform the manual calculations needed to find the circuit current and phase shift. Record the calculated values here. Do they match the measured values within reason? What has happened to the circuit with an increase in frequency? Calculated Current Calculated Phase Shift Writeup and Submission In general, for each lab you do, you will be asked to setup certain circuits, simulate them, record the results, verify the results are correct by hand, and then discuss the solution. Your lab write-up should contain a one page, single spaced discussion of the lab experiment, what went right for you, what you had difficulty with, what you learned from the experiment, how it applies to our coursework, and any other comment you can think of. In addition, you should include screen shots from the MultiSim software and any other figure, table, or diagram as necessary.

No expert has answered this question yet. You can browse … Read More...
1 Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 3.1 Laboratory Objective The objective of this laboratory is to understand the basic properties of sinusoids and sinusoid measurements. 3.2 Educational Objectives After performing this experiment, students should be able to: 1. Understand the properties of sinusoids. 2. Understand sinusoidal manipulation 3. Use a function generator 4. Obtain measurements using an oscilloscope 3.3 Background Sinusoids are sine or cosine waveforms that can describe many engineering phenomena. Any oscillatory motion can be described using sinusoids. Many types of electrical signals such as square, triangle, and sawtooth waves are modeled using sinusoids. Their manipulation incurs the understanding of certain quantities that describe sinusoidal behavior. These quantities are described below. 3.3.1 Sinusoid Characteristics Amplitude The amplitude A of a sine wave describes the height of the hills and valleys of a sinusoid. It carries the physical units of what the sinusoid is describing (volts, amps, meters, etc.). Frequency There are two types of frequencies that can describe a sinusoid. The normal frequency f is how many times the sinusoid repeats per unit time. It has units of cycles per second (s-1) or Hertz (Hz). The angular frequency ω is how many radians pass per second. Consequently, ω has units of radians per second. Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 2 Period The period T is how long a sinusoid takes to repeat one complete cycle. The period is measured in seconds. Phase The phase φ of a sinusoid causes a horizontal shift along the t-axis. The phase has units of radians. TimeShift The time shift ts of a sinusoid is a horizontal shift along the t-axis and is a time measurement of the phase. The time shift has units of seconds. NOTE: A sine wave and a cosine wave only differ by a phase shift of 90° or ?2 radians. In reality, they are the same waveform but with a different φ value. 3.3.2 Sinusoidal Relationships Figure 3.1: Sinusoid The general equation of a sinusoid is given below and refers to Figure 3.1. ?(?) = ????(?? +?) (3.1) The angular frequency is related to the normal frequency by Equation 3.2. ?= 2?? (3.2) The angular frequency is also related to the period by Equation 3.3. ?=2?? (3.3) By inspection, the normal frequency is related to the period by Equation 3.4. ? =1? (3.4) ?? Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 3 The time shift is related to the phase (radians) and the frequency by Equation 3.5. ??= ∅2?? (3.5) 3.3.3 Equipment 3.3.3.1 Inductors Inductors are electrical components that resist a change in the flow of current passing through them. They are essentially coils of wire. Inductors are electromagnets too. They are represented in schematics using the following symbol and physically using the following equipment (with or without exposed wire): Figure 3.2: Symbol and Physical Example for Inductors 3.3.3.2 Capacitors Capacitors are electrical components that store energy. This enables engineers to store electrical energy from an input source such as a battery. Some capacitors are polarized and therefore have a negative and positive plate. One plate is straight, representing the positive terminal on the device, and the other is curved, representing the negative one. Polarized capacitors are represented in schematics using the following symbol and physically using the following equipment: Figure 3.3: Symbol and Physical Example for Capacitors 3.3.3.3 Function Generator A function generator is used to create different types of electrical waveforms over a wide range of frequencies. It generates standard sine, square, and triangle waveforms and uses the analog output channel. 3.3.3.5 Oscilloscope An oscilloscope is a type of electronic test instrument that allows observation of constantly varying voltages, usually as a two-dimensional plot of one or more signals as a function of time. It displays voltage data over time for the analysis of one or two voltage measurements taken from the analog input channels of the Oscilloscope. The observed waveform can be analyzed for amplitude, frequency, time interval and more. Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 4 3.4 Procedure Follow the steps outlined below after the instructor has explained how to use the laboratory equipment 3.4.1 Sinusoidal Measurements 1. Connect the output channel of the Function Generator to the channel one of the Oscilloscope. 2. Complete Table 3.1 using the given values for voltage and frequency. Table 3.1: Sinusoid Measurements Function Generator Oscilloscope (Measured) Calculated Voltage Amplitude, A (V ) Frequency (Hz) 2*A (Vp−p ) f (Hz) T (sec) ω (rad/sec) T (sec) 2.5 1000 3 5000 3.4.2 Circuit Measurements 1. Connect the circuit in figure 3.4 below with the given resistor and capacitor NOTE: Vs from the circuit comes from the Function Generator using a BNC connector. Figure 3.4: RC Circuit Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 5 2. Using the alligator to BNC cables, connect channel one of the Oscilloscope across the capacitor and complete Table 3.2 Table 3.2: Capacitor Sinusoid Function Generator Oscilloscope (Measured) Calculated Vs (Volts) Frequency (Hz) Vc (volts) f (Hz) T (sec) ω (rad/sec) 2.5 100 3. Disconnect channel one and connect channel two of the oscilloscope across the resistor and complete table 3.3. Table 3.3: Resistor Sinusoid Function Generator Oscilloscope (Measured) Calculated Vs (Volts) Frequency (Hz) VR (volts) f (Hz) T (sec) ω (rad/sec) 2.5 100 4. Leaving channel two connected across the resistor, clip the positive lead to the positive side of the capacitor and complete table 3.4 Table 3.4: Phase Difference Function Generator Oscilloscope (Measured) Calculated Vs (volts) Frequency (Hz) Divisions Time/Div (sec) ts (sec) ɸ (rad) ɸ (degrees) 2.5 100 5. Using the data from Tables 3.2, 3.3, and 3.4, plot the capacitor sinusoidal equation and the resistor sinusoidal equation on the same graph using MATLAB. HINT: Plot over one period. 6. Kirchoff’s Voltage Law states that ??(?)=??(?)+??(?). Calculate Vs by hand using the following equation and Tables 3.2 and 3.3 ??(?)=√??2+??2???(??−???−1(????)) Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 6 3.5 New MATLAB Commands hold on  This command allows multiple graphs to be placed on the same XY axis and is placed after the first plot statement. legend (’string 1’, ’string2’, ‘string3’)  This command adds a legend to the plot. Strings must be placed in the order as the plots were generated. plot (x, y, ‘line specifiers’)  This command plots the data and uses line specifiers to differentiate between different plots on the same XY axis. In this lab, only use different line styles from the table below. Table 3.5: Line specifiers for the plot() command sqrt(X)  This command produces the square root of the elements of X. NOTE: The “help” command in MATLAB can be used to find a description and example for functions such as input.  For example, type “help input” in the command window to learn more about the input function. NOTE: Refer to section the “MATLAB Commands” sections from prior labs for previously discussed material that you may also need in order to complete this assignment. Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 7 3.6 Lab Report Requirements 1. Complete Tables 3.1, 3.2, 3.3, 3.4 (5 points each) 2. Show hand calculations for all four tables. Insert after this page (5 points each) 3. Draw the two sinusoids by hand from table 3.1. Label amplitude, period, and phase. Insert after this page. (5 points) 4. Insert MATLAB plot of Vc and VR as obtained from data in Tables 3.2 and 3.3 after this page. (5 points each) 5. Show hand calculations for Vs(t). Insert after this page. (5 points) 6. Using the data from the Tables, write: (10 points) a) Vc(t) = b) VR(t) = 7. Also, ???(?)=2.5???(628?). Write your Vs below and give reasons why they are different. (10 points) a) Vs(t) = b) Reasons: 8. Write an executive summary for this lab describing what you have done, and learned. (20 points)

1 Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 3.1 Laboratory Objective The objective of this laboratory is to understand the basic properties of sinusoids and sinusoid measurements. 3.2 Educational Objectives After performing this experiment, students should be able to: 1. Understand the properties of sinusoids. 2. Understand sinusoidal manipulation 3. Use a function generator 4. Obtain measurements using an oscilloscope 3.3 Background Sinusoids are sine or cosine waveforms that can describe many engineering phenomena. Any oscillatory motion can be described using sinusoids. Many types of electrical signals such as square, triangle, and sawtooth waves are modeled using sinusoids. Their manipulation incurs the understanding of certain quantities that describe sinusoidal behavior. These quantities are described below. 3.3.1 Sinusoid Characteristics Amplitude The amplitude A of a sine wave describes the height of the hills and valleys of a sinusoid. It carries the physical units of what the sinusoid is describing (volts, amps, meters, etc.). Frequency There are two types of frequencies that can describe a sinusoid. The normal frequency f is how many times the sinusoid repeats per unit time. It has units of cycles per second (s-1) or Hertz (Hz). The angular frequency ω is how many radians pass per second. Consequently, ω has units of radians per second. Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 2 Period The period T is how long a sinusoid takes to repeat one complete cycle. The period is measured in seconds. Phase The phase φ of a sinusoid causes a horizontal shift along the t-axis. The phase has units of radians. TimeShift The time shift ts of a sinusoid is a horizontal shift along the t-axis and is a time measurement of the phase. The time shift has units of seconds. NOTE: A sine wave and a cosine wave only differ by a phase shift of 90° or ?2 radians. In reality, they are the same waveform but with a different φ value. 3.3.2 Sinusoidal Relationships Figure 3.1: Sinusoid The general equation of a sinusoid is given below and refers to Figure 3.1. ?(?) = ????(?? +?) (3.1) The angular frequency is related to the normal frequency by Equation 3.2. ?= 2?? (3.2) The angular frequency is also related to the period by Equation 3.3. ?=2?? (3.3) By inspection, the normal frequency is related to the period by Equation 3.4. ? =1? (3.4) ?? Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 3 The time shift is related to the phase (radians) and the frequency by Equation 3.5. ??= ∅2?? (3.5) 3.3.3 Equipment 3.3.3.1 Inductors Inductors are electrical components that resist a change in the flow of current passing through them. They are essentially coils of wire. Inductors are electromagnets too. They are represented in schematics using the following symbol and physically using the following equipment (with or without exposed wire): Figure 3.2: Symbol and Physical Example for Inductors 3.3.3.2 Capacitors Capacitors are electrical components that store energy. This enables engineers to store electrical energy from an input source such as a battery. Some capacitors are polarized and therefore have a negative and positive plate. One plate is straight, representing the positive terminal on the device, and the other is curved, representing the negative one. Polarized capacitors are represented in schematics using the following symbol and physically using the following equipment: Figure 3.3: Symbol and Physical Example for Capacitors 3.3.3.3 Function Generator A function generator is used to create different types of electrical waveforms over a wide range of frequencies. It generates standard sine, square, and triangle waveforms and uses the analog output channel. 3.3.3.5 Oscilloscope An oscilloscope is a type of electronic test instrument that allows observation of constantly varying voltages, usually as a two-dimensional plot of one or more signals as a function of time. It displays voltage data over time for the analysis of one or two voltage measurements taken from the analog input channels of the Oscilloscope. The observed waveform can be analyzed for amplitude, frequency, time interval and more. Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 4 3.4 Procedure Follow the steps outlined below after the instructor has explained how to use the laboratory equipment 3.4.1 Sinusoidal Measurements 1. Connect the output channel of the Function Generator to the channel one of the Oscilloscope. 2. Complete Table 3.1 using the given values for voltage and frequency. Table 3.1: Sinusoid Measurements Function Generator Oscilloscope (Measured) Calculated Voltage Amplitude, A (V ) Frequency (Hz) 2*A (Vp−p ) f (Hz) T (sec) ω (rad/sec) T (sec) 2.5 1000 3 5000 3.4.2 Circuit Measurements 1. Connect the circuit in figure 3.4 below with the given resistor and capacitor NOTE: Vs from the circuit comes from the Function Generator using a BNC connector. Figure 3.4: RC Circuit Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 5 2. Using the alligator to BNC cables, connect channel one of the Oscilloscope across the capacitor and complete Table 3.2 Table 3.2: Capacitor Sinusoid Function Generator Oscilloscope (Measured) Calculated Vs (Volts) Frequency (Hz) Vc (volts) f (Hz) T (sec) ω (rad/sec) 2.5 100 3. Disconnect channel one and connect channel two of the oscilloscope across the resistor and complete table 3.3. Table 3.3: Resistor Sinusoid Function Generator Oscilloscope (Measured) Calculated Vs (Volts) Frequency (Hz) VR (volts) f (Hz) T (sec) ω (rad/sec) 2.5 100 4. Leaving channel two connected across the resistor, clip the positive lead to the positive side of the capacitor and complete table 3.4 Table 3.4: Phase Difference Function Generator Oscilloscope (Measured) Calculated Vs (volts) Frequency (Hz) Divisions Time/Div (sec) ts (sec) ɸ (rad) ɸ (degrees) 2.5 100 5. Using the data from Tables 3.2, 3.3, and 3.4, plot the capacitor sinusoidal equation and the resistor sinusoidal equation on the same graph using MATLAB. HINT: Plot over one period. 6. Kirchoff’s Voltage Law states that ??(?)=??(?)+??(?). Calculate Vs by hand using the following equation and Tables 3.2 and 3.3 ??(?)=√??2+??2???(??−???−1(????)) Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 6 3.5 New MATLAB Commands hold on  This command allows multiple graphs to be placed on the same XY axis and is placed after the first plot statement. legend (’string 1’, ’string2’, ‘string3’)  This command adds a legend to the plot. Strings must be placed in the order as the plots were generated. plot (x, y, ‘line specifiers’)  This command plots the data and uses line specifiers to differentiate between different plots on the same XY axis. In this lab, only use different line styles from the table below. Table 3.5: Line specifiers for the plot() command sqrt(X)  This command produces the square root of the elements of X. NOTE: The “help” command in MATLAB can be used to find a description and example for functions such as input.  For example, type “help input” in the command window to learn more about the input function. NOTE: Refer to section the “MATLAB Commands” sections from prior labs for previously discussed material that you may also need in order to complete this assignment. Laboratory 3 – Sinusoids in Engineering: Measurement and Analysis of Harmonic Signals 7 3.6 Lab Report Requirements 1. Complete Tables 3.1, 3.2, 3.3, 3.4 (5 points each) 2. Show hand calculations for all four tables. Insert after this page (5 points each) 3. Draw the two sinusoids by hand from table 3.1. Label amplitude, period, and phase. Insert after this page. (5 points) 4. Insert MATLAB plot of Vc and VR as obtained from data in Tables 3.2 and 3.3 after this page. (5 points each) 5. Show hand calculations for Vs(t). Insert after this page. (5 points) 6. Using the data from the Tables, write: (10 points) a) Vc(t) = b) VR(t) = 7. Also, ???(?)=2.5???(628?). Write your Vs below and give reasons why they are different. (10 points) a) Vs(t) = b) Reasons: 8. Write an executive summary for this lab describing what you have done, and learned. (20 points)

info@checkyourstudy.com
Design of Electrical Systems Name: ______________________________ Note: All problems weighted equally. Show your work on all problems to receive partial credit. Resources: a) The Fundamental Logic Gate Family, Author Unknown b) Electric Devices and Circuit Theory 7th Edition, Boylestad c) Introductory Circuit Analysis 10th Edition, Boylestad d) Power Supplies (Voltage Regulators) Chapter 19, Boylestad e) Electronic Devices and Circuit Theory Chapter 5, Boylestad f) Operational Amplifiers Handout, Self g) Switch Mode Power Supplies, Philips Semiconductor h) NI Tutorial 13714-en October 6, 2013 i) NI Tutorial 13714-en V2.0 October 6, 2013 j) National Instruments Circuit Design Applications http://www.ni.com/multisim/applications/pro/ k) ENERGY STAR https://www.energystar.gov/index.cfm?c=most_efficient.me_comp_monitor_under_23_inches l) Manufactures Device Data Sheets 1) For the VDB shown below, please find the following quantities and plot the load line (Saturation / Cutoff), Q pt (Quiescent Point) and sketch input waveform and output wave form. Remember to test for Exact vs. Approximate Method. Given Bdc = hfe = 150 and RL of 10KΩ. Efficiency _ Class _____ Degrees ___ VR2_______ VE_______ VC _______ VCE ______ IC _______ IE _______ IB _______ PD _______ re’ _______ Av _______ mpp ______ Vout______ What is the effect of reducing RL to 500Ω ________________________________ What is the effect of reducing the Source Frequency to 50 Hz ________________ | | | | | | |____________________________________________ 2) For the following Networks, please complete the Truth Tables, Logic Gate Type, provide the Boolean Logic Expression. A | Vout 0 | 1 | Logic Gate Type _______ Boolean Logic Expression _________ A B| Vout 0 0| 0 1| 1 0| 1 1| Logic Gate Type _______ Boolean Logic Expression _________ A B C| Vout 0 0 0| 0 0 1| 0 1 0| 0 1 1| 1 0 0| 1 0 1| 1 1 0| 1 1 1| Logic Gate Type _______ Boolean Logic Expression _________ Operation of Transistors ____________ 3) For the Network shown below, please refer to Electronic Devices and Circuit Theory Chapter 5, Boylestad to solve for the following values: Given: Bdc1 = hfe1 = 55 Bdc2 = hfe2 = 70 Bdc Total ______ IB1 _________ IB2 _________ VC1 __________ VC2 __________ VE1 __________ VE2 __________ What is this Transistor Configuration? _______________________ What are the advantages of this Transistor Configuration? _________________________________________ _________________________________________ _________________________________________ _________________________________________ 4) Design a Four (4) output Power Supply with the following Specifications, Provide a clean schematic sketch of circuit (Please provide the schematic sketch on a separate piece of graph paper). Use a straight edge and label everything. Refer to Data Sheets as necessary. Specifications: 120 VAC rms 60 Hz Source Positive + 15 VDC Driving a 15Ω 20 Watt Resistive Load Positive +8 VDC Driving a 10Ω 2 Watt Resistive Load Negative – 12 VDC Driving a 10Ω 2 Watt Resistive Load Negative – 5 VDC Driving a 4Ω 2 Watt Resistive Load Parts available (Must use parts): 1x 120 VAC 40 Volt 3.5 Amp Center Tap Transformer 1x Fuse 1x Bridge Rectifier 12 Amp 1x LM7808 1x LM7815 1x LM7905 1x LM7912 Psource _____________ Fuse size with 25% Service Factor, 1-10 Amps increments of 1A, 10 – 50 Amps increments of 5 Amps ______ Are we exceeding Power Dissipation of any components? If so please identify and provide a brief explanation: _________________________________________________________________ _________________________________________________________________ 5) For the circuit shown below please calculate the following quantities, and Plot the Trans-Conductance Curve (Transfer Curve), (Please provide the plot on a separate piece of graph paper): You will need to refer to the 2N3819 N-Channel JFET ON Semiconductor Data Sheet Posted on Bb. VDS _________ VP ___________ VGS(off) ______ VS __________ VD __________ VG __________ PDD _________ PSource ______ VGSQ ________ IDQ __________ 6) Determine both the Upper and Lower Cutoff frequencies. Sketch Bode plot and label everything including dB Role-Off. Construct Network in Multisim and perform AC Analysis verifying frequency response and Upper and Lower Cutoff Frequencies in support of your calculations. Attach Screen shot of your Multisim Model and AC Analysis. Repeat the above for a 2nd Order Active BP Filter. You will need to research this configuration. Make sure that you use the same values for R and C. Upper and Lower Cutoff Frequencies are determined by for the 2nd Order Active BP Filter fc = 1/(2(3.14)SQRT(R1R2C1C2)). Demonstrate a change in Roll-Off from 1st Order to 2nd Order. First Order: Lower Cutoff Frequency ________ Upper Cutoff Frequency ________ Roll-Off ______________________ | | | | | | | |_____________________________________________________________ Second Order: Lower Cutoff Frequency ________ Upper Cutoff Frequency ________ Roll-Off ______________________ | | | | | | |_____________________________________________________________ 7) The following questions relate to LED Backlight LCD Monitors. (Please feel free to use more paper if need be). See Resources. Please explain the differences between LED Backlight LCD Monitor, LCD and CCFL Monitors (Cold Cathode Fluorescent Lamp) Monitors. What are some advantages of LED Backlight LCD Monitors when compared with LCD and CCFL Monitors? What color LEDs are used in the creation of an LED Backlight LCD Monitor? Does a Black Background use less energy than a White Background? If you can believe the hype, how and why are LED Backlight LCD Monitors among the most energy efficient, higher than heirs apparent? 8) In this problem the goal is to verify the Transfer Characteristics of the 2N7000G Enhancement Mode N-Channel MOSFET against the manufactures Data Sheets. Please create in Multisim a Model as exampled below. First Plot by hand on Graph Paper various VGS Voltages vs ID. Second simulate using the DC Sweep Analysis. From these results verify against the 2N7000G ON Semiconductor Data Sheet Posted on Bb, remembering that the 2N7000G ON Semiconductor Data Sheet includes both Tabulated Data and Figure 2. Transfer Characteristics. Attach all results, screen shots and write a brief description of your work. • I estimate that my mark for this exam will be: ________ % • Time spent on this exam: __________ Hours • Average of time spent per week on work for EGR-330 (outside class sessions): ______________ Hours

Design of Electrical Systems Name: ______________________________ Note: All problems weighted equally. Show your work on all problems to receive partial credit. Resources: a) The Fundamental Logic Gate Family, Author Unknown b) Electric Devices and Circuit Theory 7th Edition, Boylestad c) Introductory Circuit Analysis 10th Edition, Boylestad d) Power Supplies (Voltage Regulators) Chapter 19, Boylestad e) Electronic Devices and Circuit Theory Chapter 5, Boylestad f) Operational Amplifiers Handout, Self g) Switch Mode Power Supplies, Philips Semiconductor h) NI Tutorial 13714-en October 6, 2013 i) NI Tutorial 13714-en V2.0 October 6, 2013 j) National Instruments Circuit Design Applications http://www.ni.com/multisim/applications/pro/ k) ENERGY STAR https://www.energystar.gov/index.cfm?c=most_efficient.me_comp_monitor_under_23_inches l) Manufactures Device Data Sheets 1) For the VDB shown below, please find the following quantities and plot the load line (Saturation / Cutoff), Q pt (Quiescent Point) and sketch input waveform and output wave form. Remember to test for Exact vs. Approximate Method. Given Bdc = hfe = 150 and RL of 10KΩ. Efficiency _ Class _____ Degrees ___ VR2_______ VE_______ VC _______ VCE ______ IC _______ IE _______ IB _______ PD _______ re’ _______ Av _______ mpp ______ Vout______ What is the effect of reducing RL to 500Ω ________________________________ What is the effect of reducing the Source Frequency to 50 Hz ________________ | | | | | | |____________________________________________ 2) For the following Networks, please complete the Truth Tables, Logic Gate Type, provide the Boolean Logic Expression. A | Vout 0 | 1 | Logic Gate Type _______ Boolean Logic Expression _________ A B| Vout 0 0| 0 1| 1 0| 1 1| Logic Gate Type _______ Boolean Logic Expression _________ A B C| Vout 0 0 0| 0 0 1| 0 1 0| 0 1 1| 1 0 0| 1 0 1| 1 1 0| 1 1 1| Logic Gate Type _______ Boolean Logic Expression _________ Operation of Transistors ____________ 3) For the Network shown below, please refer to Electronic Devices and Circuit Theory Chapter 5, Boylestad to solve for the following values: Given: Bdc1 = hfe1 = 55 Bdc2 = hfe2 = 70 Bdc Total ______ IB1 _________ IB2 _________ VC1 __________ VC2 __________ VE1 __________ VE2 __________ What is this Transistor Configuration? _______________________ What are the advantages of this Transistor Configuration? _________________________________________ _________________________________________ _________________________________________ _________________________________________ 4) Design a Four (4) output Power Supply with the following Specifications, Provide a clean schematic sketch of circuit (Please provide the schematic sketch on a separate piece of graph paper). Use a straight edge and label everything. Refer to Data Sheets as necessary. Specifications: 120 VAC rms 60 Hz Source Positive + 15 VDC Driving a 15Ω 20 Watt Resistive Load Positive +8 VDC Driving a 10Ω 2 Watt Resistive Load Negative – 12 VDC Driving a 10Ω 2 Watt Resistive Load Negative – 5 VDC Driving a 4Ω 2 Watt Resistive Load Parts available (Must use parts): 1x 120 VAC 40 Volt 3.5 Amp Center Tap Transformer 1x Fuse 1x Bridge Rectifier 12 Amp 1x LM7808 1x LM7815 1x LM7905 1x LM7912 Psource _____________ Fuse size with 25% Service Factor, 1-10 Amps increments of 1A, 10 – 50 Amps increments of 5 Amps ______ Are we exceeding Power Dissipation of any components? If so please identify and provide a brief explanation: _________________________________________________________________ _________________________________________________________________ 5) For the circuit shown below please calculate the following quantities, and Plot the Trans-Conductance Curve (Transfer Curve), (Please provide the plot on a separate piece of graph paper): You will need to refer to the 2N3819 N-Channel JFET ON Semiconductor Data Sheet Posted on Bb. VDS _________ VP ___________ VGS(off) ______ VS __________ VD __________ VG __________ PDD _________ PSource ______ VGSQ ________ IDQ __________ 6) Determine both the Upper and Lower Cutoff frequencies. Sketch Bode plot and label everything including dB Role-Off. Construct Network in Multisim and perform AC Analysis verifying frequency response and Upper and Lower Cutoff Frequencies in support of your calculations. Attach Screen shot of your Multisim Model and AC Analysis. Repeat the above for a 2nd Order Active BP Filter. You will need to research this configuration. Make sure that you use the same values for R and C. Upper and Lower Cutoff Frequencies are determined by for the 2nd Order Active BP Filter fc = 1/(2(3.14)SQRT(R1R2C1C2)). Demonstrate a change in Roll-Off from 1st Order to 2nd Order. First Order: Lower Cutoff Frequency ________ Upper Cutoff Frequency ________ Roll-Off ______________________ | | | | | | | |_____________________________________________________________ Second Order: Lower Cutoff Frequency ________ Upper Cutoff Frequency ________ Roll-Off ______________________ | | | | | | |_____________________________________________________________ 7) The following questions relate to LED Backlight LCD Monitors. (Please feel free to use more paper if need be). See Resources. Please explain the differences between LED Backlight LCD Monitor, LCD and CCFL Monitors (Cold Cathode Fluorescent Lamp) Monitors. What are some advantages of LED Backlight LCD Monitors when compared with LCD and CCFL Monitors? What color LEDs are used in the creation of an LED Backlight LCD Monitor? Does a Black Background use less energy than a White Background? If you can believe the hype, how and why are LED Backlight LCD Monitors among the most energy efficient, higher than heirs apparent? 8) In this problem the goal is to verify the Transfer Characteristics of the 2N7000G Enhancement Mode N-Channel MOSFET against the manufactures Data Sheets. Please create in Multisim a Model as exampled below. First Plot by hand on Graph Paper various VGS Voltages vs ID. Second simulate using the DC Sweep Analysis. From these results verify against the 2N7000G ON Semiconductor Data Sheet Posted on Bb, remembering that the 2N7000G ON Semiconductor Data Sheet includes both Tabulated Data and Figure 2. Transfer Characteristics. Attach all results, screen shots and write a brief description of your work. • I estimate that my mark for this exam will be: ________ % • Time spent on this exam: __________ Hours • Average of time spent per week on work for EGR-330 (outside class sessions): ______________ Hours

info@checkyourstudy.com Operations Team Whatsapp( +91 9911743277)
Lab Description: Follow the instructions in the lab tasks below to behaviorially create and simulate a flip-flop. Afterwards, you will create a register and Arithmetic Logic Unit (ALU). Refer to Module 7 from the Digilent Real Digital website for more information about ALUs. These two components are the main components required to create an accumulator datapath. This accumulator datapath will act like a simple processor; the ALU will execute simple arithmetic/logic operations and each result will be stored in the register. In an accumulator, the value of the register will be upedated with each operation; the register is used as an input to the ALU and the newly computed result of the operation will be stored back into the register. You will create and implement this accumulator datapath in the last task of this lab. However, you will need to add an additional component to enable it to clearly operate on the FPGA board. You will create and use a clock divider to create a slower version of the FPGA board’s clock when you implement the accumulator datapath on the FPGA board. Refer to Module 10 from the Digilent Real Digital website for more information about clock dividers. Lab Tasks: 1. Create a behavioral VHDL module for a Rising-Edge Triggered (RET) D-Flip-Flop (DFF): a. In your design, use inputs “D” (data), “CLK” (the clock), “RST” (an asynchronous reset), “SET” (a synchronous set or preset signal), “CE” (clock enable), and output “Q” b. Create a VHDL test bench and simulate the flip-flop. Be sure to show the following behaviors with your simulation: i. The output “Q” sampling a ‘0’ from the input “D” ii. The output “Q” sampling a ‘1’ from the input “D” iii. The correct operation of the asynchronous reset iv. The correct operation of the synchronous preset v. The correct operation of the clock enable c. Include a screenshot of your simulation on the lab’s cover sheet. Label each of these behaviors on the waveform (it is ok to print out your cover sheet and write each behavior on the waveform). 2. Create a behavioral VHDL module for a 4-bit Arithmetic Logic Unit (ALU): a. I suggest you refer to Module 7 from the Digilent Real Digital website (in particular, the sections about ALU circuits and behavioral VHDL ALU descriptions). This 4-bit ALU will calculate arithmetic and logical expressions on two 4-bit numbers. Use behavioral expressions for the arithmetic and logic expressions (do not use port map statements to create a structural design using your ripple-carry adder from lab 3). Assume that the select input (or opcode) is 2-bits and is defined as shown in the table below: Opcode Function 00 A 01 A plus 1 10 A plus B 11 A and B b. Create a VHDL test bench to test your ALU. Use two input signal (the 4-bit values for A and B) combinations to test each operation of the ALU. Simulate your design and verify your output. Include a screenshot of your simulation on the lab’s cover sheet. 3. Create an accumulator datapath: a. First, create a 4-bit register. This is very similar to your flip-flop design from lab task 1. Ensure that your 4-bit register has inputs “D” (data), “CLK” (the clock), and “RST” (an asynchronous reset), and an output “Q”. Create a test bench and ensure that your 4-bit register operates correctly. b. Next, create a design module for the accumulator datapath and import your 4-bit register, 4-bit ALU, and seven-sgement display decoder (from lab 2) as components to this system. Connect your register, ALU, and seven-segment display decoder as follows: i. Connect the output of your ALU to the “D” input of your register ii. Connect the “Q” output of your register to both the “A” input of your ALU and the input of your seven-segement display iii. You should be left with four overall inputs: the “B” input of your ALU, the opcode input of your ALU, the CLK, and RST iv. You should be left with one overall output: the seven-segment display output c. Create a test bench to simulate the behavior of your accumulator datapath. In your test bench, simulate a few clock cycles to verify the correct operation of your system. d. Before implementing this system on the FPGA board, create and add one additional component to your system. Create and add a clock divider to this system; the input will be the board’s clock and the output will be a slower version of the clock to use for the register. Design your clock divider to slow the clock frequency to 1 Hz (1 clock cycle per second). Note that the clock on the lab FPGA board (Spartan 3) has a frequency of 50 MHz. If you purchased your board, the FPGA Basys 3 or Nexys 4 DDR FPGA board has a frequency of 100 MHz. I highly recommend taking a look at “Binary counters in VHDL” from Module 10 from the Digilent Real Digital website for information about clock dividers. e. Now, implement this system on the FPGA board. Connect the data input to four switches, connect the ALU opcode inputs to two buttons, the RST signal to one button, the CLK signal to the board’s clock, and the seven-segment display output to the seven-segment display. f. Ask the instructor to check your design, simulation waveforms, and FPGA board implementation of your circuit

Lab Description: Follow the instructions in the lab tasks below to behaviorially create and simulate a flip-flop. Afterwards, you will create a register and Arithmetic Logic Unit (ALU). Refer to Module 7 from the Digilent Real Digital website for more information about ALUs. These two components are the main components required to create an accumulator datapath. This accumulator datapath will act like a simple processor; the ALU will execute simple arithmetic/logic operations and each result will be stored in the register. In an accumulator, the value of the register will be upedated with each operation; the register is used as an input to the ALU and the newly computed result of the operation will be stored back into the register. You will create and implement this accumulator datapath in the last task of this lab. However, you will need to add an additional component to enable it to clearly operate on the FPGA board. You will create and use a clock divider to create a slower version of the FPGA board’s clock when you implement the accumulator datapath on the FPGA board. Refer to Module 10 from the Digilent Real Digital website for more information about clock dividers. Lab Tasks: 1. Create a behavioral VHDL module for a Rising-Edge Triggered (RET) D-Flip-Flop (DFF): a. In your design, use inputs “D” (data), “CLK” (the clock), “RST” (an asynchronous reset), “SET” (a synchronous set or preset signal), “CE” (clock enable), and output “Q” b. Create a VHDL test bench and simulate the flip-flop. Be sure to show the following behaviors with your simulation: i. The output “Q” sampling a ‘0’ from the input “D” ii. The output “Q” sampling a ‘1’ from the input “D” iii. The correct operation of the asynchronous reset iv. The correct operation of the synchronous preset v. The correct operation of the clock enable c. Include a screenshot of your simulation on the lab’s cover sheet. Label each of these behaviors on the waveform (it is ok to print out your cover sheet and write each behavior on the waveform). 2. Create a behavioral VHDL module for a 4-bit Arithmetic Logic Unit (ALU): a. I suggest you refer to Module 7 from the Digilent Real Digital website (in particular, the sections about ALU circuits and behavioral VHDL ALU descriptions). This 4-bit ALU will calculate arithmetic and logical expressions on two 4-bit numbers. Use behavioral expressions for the arithmetic and logic expressions (do not use port map statements to create a structural design using your ripple-carry adder from lab 3). Assume that the select input (or opcode) is 2-bits and is defined as shown in the table below: Opcode Function 00 A 01 A plus 1 10 A plus B 11 A and B b. Create a VHDL test bench to test your ALU. Use two input signal (the 4-bit values for A and B) combinations to test each operation of the ALU. Simulate your design and verify your output. Include a screenshot of your simulation on the lab’s cover sheet. 3. Create an accumulator datapath: a. First, create a 4-bit register. This is very similar to your flip-flop design from lab task 1. Ensure that your 4-bit register has inputs “D” (data), “CLK” (the clock), and “RST” (an asynchronous reset), and an output “Q”. Create a test bench and ensure that your 4-bit register operates correctly. b. Next, create a design module for the accumulator datapath and import your 4-bit register, 4-bit ALU, and seven-sgement display decoder (from lab 2) as components to this system. Connect your register, ALU, and seven-segment display decoder as follows: i. Connect the output of your ALU to the “D” input of your register ii. Connect the “Q” output of your register to both the “A” input of your ALU and the input of your seven-segement display iii. You should be left with four overall inputs: the “B” input of your ALU, the opcode input of your ALU, the CLK, and RST iv. You should be left with one overall output: the seven-segment display output c. Create a test bench to simulate the behavior of your accumulator datapath. In your test bench, simulate a few clock cycles to verify the correct operation of your system. d. Before implementing this system on the FPGA board, create and add one additional component to your system. Create and add a clock divider to this system; the input will be the board’s clock and the output will be a slower version of the clock to use for the register. Design your clock divider to slow the clock frequency to 1 Hz (1 clock cycle per second). Note that the clock on the lab FPGA board (Spartan 3) has a frequency of 50 MHz. If you purchased your board, the FPGA Basys 3 or Nexys 4 DDR FPGA board has a frequency of 100 MHz. I highly recommend taking a look at “Binary counters in VHDL” from Module 10 from the Digilent Real Digital website for information about clock dividers. e. Now, implement this system on the FPGA board. Connect the data input to four switches, connect the ALU opcode inputs to two buttons, the RST signal to one button, the CLK signal to the board’s clock, and the seven-segment display output to the seven-segment display. f. Ask the instructor to check your design, simulation waveforms, and FPGA board implementation of your circuit

checkyourstudy.com Whatsapp +919911743277
Biomedical Signal and Image Processing (4800_420_001) Assigned on September 12th, 2017 Assignment 4 – Noise and Correlation 1. If a signal is measured as 2.5 V and the noise is 28 mV (28 × 10−3 V), what is the SNR in dB? 2. A single sinusoidal signal is found with some noise. If the RMS value of the noise is 0.5 V and the SNR is 10 dB, what is the RMS amplitude of the sinusoid? 3. The file signal_noise.mat contains a variable x that consists of a 1.0-V peak sinusoidal signal buried in noise. What is the SNR for this signal and noise? Assume that the noise RMS is much greater than the signal RMS. Note: “signal_noise.mat” and other files used in these assignments can be downloaded from the content area of Brightspace, within the “Data Files for Exercises” folder. These files can be opened in Matlab by copying into the active folder and double-clicking on the file or using the Matlab load command using the format: load(‘signal_noise.mat’). To discover the variables within the files use the Matlab who command. 4. An 8-bit ADC converter that has an input range of ±5 V is used to convert a signal that ranges between ±2 V. What is the SNR of the input if the input noise equals the quantization noise of the converter? Hint: Refer to Equation below to find the quantization noise: 5. The file filter1.mat contains the spectrum of a fourth-order lowpass filter as variable x in dB. The file also contains the corresponding frequencies of x in variable freq. Plot the spectrum of this filter both as dB versus log frequency and as linear amplitude versus linear frequency. The frequency axis should range between 10 and 400 Hz in both plots. Hint: Use Equation below to convert: Biomedical Signal and Image Processing (4800_420_001) Assigned on September 12th, 2017 6. Generate one cycle of the square wave similar to the one shown below in a 500-point MATLAB array. Determine the RMS value of this waveform. [Hint: When you take the square of the data array, be sure to use a period before the up arrow so that MATLAB does the squaring point-by-point (i.e., x.^2).]. 7. A resistor produces 10 μV noise (i.e., 10 × 10−6 V noise) when the room temperature is 310 K and the bandwidth is 1 kHz (i.e., 1000 Hz). What current noise would be produced by this resistor? 8. A 3-ma current flows through both a diode (i.e., a semiconductor) and a 20,000-Ω (i.e., 20-kΩ) resistor. What is the net current noise, in? Assume a bandwidth of 1 kHz (i.e., 1 × 103 Hz). Which of the two components is responsible for producing the most noise? 9. Determine if the two signals, x and y, in file correl1.mat are correlated by checking the angle between them. 10. Modify the approach used in Practice Problem 3 to find the angle between short signals: Do not attempt to plot these vectors as it would require a 6-dimensional plot!

Biomedical Signal and Image Processing (4800_420_001) Assigned on September 12th, 2017 Assignment 4 – Noise and Correlation 1. If a signal is measured as 2.5 V and the noise is 28 mV (28 × 10−3 V), what is the SNR in dB? 2. A single sinusoidal signal is found with some noise. If the RMS value of the noise is 0.5 V and the SNR is 10 dB, what is the RMS amplitude of the sinusoid? 3. The file signal_noise.mat contains a variable x that consists of a 1.0-V peak sinusoidal signal buried in noise. What is the SNR for this signal and noise? Assume that the noise RMS is much greater than the signal RMS. Note: “signal_noise.mat” and other files used in these assignments can be downloaded from the content area of Brightspace, within the “Data Files for Exercises” folder. These files can be opened in Matlab by copying into the active folder and double-clicking on the file or using the Matlab load command using the format: load(‘signal_noise.mat’). To discover the variables within the files use the Matlab who command. 4. An 8-bit ADC converter that has an input range of ±5 V is used to convert a signal that ranges between ±2 V. What is the SNR of the input if the input noise equals the quantization noise of the converter? Hint: Refer to Equation below to find the quantization noise: 5. The file filter1.mat contains the spectrum of a fourth-order lowpass filter as variable x in dB. The file also contains the corresponding frequencies of x in variable freq. Plot the spectrum of this filter both as dB versus log frequency and as linear amplitude versus linear frequency. The frequency axis should range between 10 and 400 Hz in both plots. Hint: Use Equation below to convert: Biomedical Signal and Image Processing (4800_420_001) Assigned on September 12th, 2017 6. Generate one cycle of the square wave similar to the one shown below in a 500-point MATLAB array. Determine the RMS value of this waveform. [Hint: When you take the square of the data array, be sure to use a period before the up arrow so that MATLAB does the squaring point-by-point (i.e., x.^2).]. 7. A resistor produces 10 μV noise (i.e., 10 × 10−6 V noise) when the room temperature is 310 K and the bandwidth is 1 kHz (i.e., 1000 Hz). What current noise would be produced by this resistor? 8. A 3-ma current flows through both a diode (i.e., a semiconductor) and a 20,000-Ω (i.e., 20-kΩ) resistor. What is the net current noise, in? Assume a bandwidth of 1 kHz (i.e., 1 × 103 Hz). Which of the two components is responsible for producing the most noise? 9. Determine if the two signals, x and y, in file correl1.mat are correlated by checking the angle between them. 10. Modify the approach used in Practice Problem 3 to find the angle between short signals: Do not attempt to plot these vectors as it would require a 6-dimensional plot!

Whatsapp +919911743277